====== Open CNC Project ======

===== Résumé =====

Une CNC Open Source faîte à partir de pièces imprimées et d'éléments de quincaillerie facilement disponible, type RepRap.

Plusieurs projets possibles, commencer par choisir un modèle.

===== Liste de matériel =====

[[https://mh8.fr/resources/files/RS_CNC_mecanical_manual_assembly.pdf|Notice d'assemblage]]

==== Pièces imprimés ====


++++ Tableau des pièces imprimées |
<WRAP 100% round>


{| class="table table-striped table-condensed" style="text-align: center;"
! style="text-align: center;" | Image
! style="text-align: center;" | Pièce
! style="text-align: center;" | Quantité
! style="text-align: center;" | Infill
! style="text-align: center;" | Imprimé par
! style="text-align: center;" | Durée d'impression
|- 
| {{projets:opencnc:bottom-corner-a.jpg?50}}
| style="vertical-align:middle;color:green; font-weight:bold;" | Bottom corner A - 18x100mm 
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 8h30 //(x2)//
|- 
| {{projets:opencnc:bottom-corner-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;"| Bottom corner B - 18x100mm
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 8h30 //(x2)//
|-
| {{projets:opencnc:buttons-plate.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Buttons plate
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 20%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h45
|-
| {{projets:opencnc:cable-gromet.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Cable Grommet
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 45min
|-
| {{projets:opencnc:corner-x-back-left.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Corner X Back Left - 18x100mm
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 7h
|-
| {{projets:opencnc:corner-x-back-left.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Corner X Back Right - 18x100mm
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 5h30
|-
| {{projets:opencnc:dolly-base.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Dolly Base
| style="vertical-align:middle;" | 4
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 5h30 //(x4)//
|-
| {{projets:opencnc:dolly-bottom.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Dolly Bottom
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 5h
|-
| {{projets:opencnc:dolly-inter.jpg?50}}
| style="vertical-align:middle;color:green; font-weight:bold;" | Dolly Inter
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 5h
|-
| {{projets:opencnc:dolly-top.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Dolly Top
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 8h30
|-
| {{projets:opencnc:drill-model.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Drill Model
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 2h30
|-
| {{projets:opencnc:plate-fix.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Plate Fix
| style="vertical-align:middle;" | 6
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 20min //(x6)//
|-
| {{projets:opencnc:plate-wheel.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Plate Wheel
| style="vertical-align:middle;" | 6
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 45min //(x6)//
|-
| {{projets:opencnc:router-65mm.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Router 65mm
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 10h
|-
| {{projets:opencnc:square-plate.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Square Plate
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 2h30
|-
| {{projets:opencnc:tft-holder.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | TFT Holder
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h
|-
| {{projets:opencnc:tft-cover.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | TFT Cover
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 2h30
|-
| {{projets:opencnc:top-corner.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Top Corner - 18x100mm
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 6h30 //(x2)//
|-
| {{projets:opencnc:x-belt-holder.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Belt Holder
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 2h30
|-
| {{projets:opencnc:x-chain-holder.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Chain Holder
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 45min
|-
| {{projets:opencnc:x-motor.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Motor
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 7h30
|-
| {{projets:opencnc:x-pulley.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Pulley
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 2h
|-
| {{projets:opencnc:x-belt-tensionner-1.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Belt Tensionner 1
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h
|-
| {{projets:opencnc:x-belt-tensionner-2.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Belt Tensionner 2
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 30min
|-
| {{projets:opencnc:x-left-30.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Left 30
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;  | 5H
|-
| {{projets:opencnc:x-left-30.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | X Right 30
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;  | 4h30
|-
| {{projets:opencnc:y-back-bearing-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Back Bearing A
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h30
|-
| {{projets:opencnc:y-back-bearing-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Back Bearing B
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h30
|-
| {{projets:opencnc:y-belt.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Belt
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 3h //(x2)//
|-
| {{projets:opencnc:y-belt-holder.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Belt Holder
| style="vertical-align:middle;" | 2
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h //(x2)//
|-
| {{projets:opencnc:y-belt-tensionner-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Belt Tensionner A
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 2h
|-
| {{projets:opencnc:y-belt-tensionner-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Belt Tensionner B
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 2h
|-
| {{projets:opencnc:y-holder-30.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Holder 30 A
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 4h
|-
| {{projets:opencnc:y-holder-30.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Holder 30 B
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 4h
|-
| {{projets:opencnc:y-holder-switch.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Holder 30 Switch
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 3h45
|-
| {{projets:opencnc:y-motor.jpg?50}}
| style="vertical-align:middle;" | Y Motor
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | -
| style="vertical-align:middle;" | 3h30
|-
| {{projets:opencnc:y-chain.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Y Chain
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 45min
|-
| {{projets:opencnc:z-bearing-blocker.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Z Bearing Blocker
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 15min
|-
| {{projets:opencnc:z-plate.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Z Plate
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 30/40%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 8h45
|-
| {{projets:opencnc:z-screw-blocker.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Z Screw Blocker
| style="vertical-align:middle;" | 1
| style="vertical-align:middle;" | 40%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 30min
|-
| {{projets:opencnc:z-scroll-wheel.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | Z Scroll Wheel
| style="vertical-align:middle;" | 1  
| style="vertical-align:middle;" | 30%
| style="vertical-align:middle;" | Mathieu
| style="vertical-align:middle;" | 1h15
|-

| {{projets:opencnc:xy-junction-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | XY Junction A - 18x100mm
| style="vertical-align:middle;" | 1  
| style="vertical-align:middle;" | 30%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 5h15
|-
| {{projets:opencnc:xy-junction-a.jpg?50}}
| style="vertical-align:middle; color:green; font-weight:bold;" | XY Junction B - 18x100mm
| style="vertical-align:middle;" | 1  
| style="vertical-align:middle;" | 30%
| style="vertical-align:middle;" | Christophe
| style="vertical-align:middle;" | 5h15
|-

| {{projets:opencnc:spacer-plate-alu.jpg?50}}
| style="vertical-align:middle;" | Spacer Alu Plate
| style="vertical-align:middle;" | 1  
| style="vertical-align:middle;" | 30%
| style="vertical-align:middle;" | -
| style="vertical-align:middle;" | 45min
|-
|}

</WRAP>
++++


==== Pièces Mécaniques & Quincaillerie ====

^  Nom  ^  Quantité  ^  Fournisseur  ^  Prix unit.  ^  Prix total  ^  Prix cumul  ^
|  Tige filetée M10 830mm  |  1  |  [[https://www.leroymerlin.fr/v3/p/produits/tige-filetee-inox-brut-l-1000-x-diam-10-mm-alfer-e54329|Leroy Merlin]]  |  7,90€/m  |  7,90 €  |  7,90 €  |
|  Tiges filetées M8 217mm  |  4  |  [[https://www.leroymerlin.fr/v3/p/produits/tige-filetee-inox-brut-l-1000-x-diam-8-mm-alfer-e54331|Leroy Merlin]]  |  5,30€/m  |  5,30 €  |  13,20 €  |
|  Tiges filetées M8 102mm  |  8  |  [[https://www.leroymerlin.fr/v3/p/produits/tige-filetee-inox-brut-l-1000-x-diam-8-mm-alfer-e54331|Leroy Merlin]]  |  5,30€/m  |  5,30 €  |  18,50 €  |
|  Tige lisse 8mm longueur 92mm  |  1  |  ??  |  -  |  -  |  -  |
|  Tige lisse 8mm longueur 688mm  |  1  |  ADD??  |  -  |  -  |  -  |
|  Règle de maçon 100x18mm, longueur 722mm  |  2  |  [[https://www.leroymerlin.fr/v3/p/produits/regle-sans-embout-nespoli-100-cm-e67191|Leroy Merlin]]  |  8,90€/m  |  17,80 €  |  36,30 €  |
|  Règle de maçon 100x18mm, Longueur 266mm  |  2  |  [[https://www.leroymerlin.fr/v3/p/produits/regle-sans-embout-nespoli-100-cm-e67191|Leroy Merlin]]  |  8,90€/m  |  -  |  36,30 €  |
|  Règle de maçon 100x18mm, longueur 600mm  |  2  |  [[https://www.leroymerlin.fr/v3/p/produits/regle-sans-embout-nespoli-100-cm-e67191|Leroy Merlin]]  |  8,90€/m  |  17,80 €  |  54,10 €  |
|  Règle de maçon 100x18mm, longueur 750mm  |  2  |  [[https://www.leroymerlin.fr/v3/p/produits/regle-sans-embout-nespoli-100-cm-e67191|Leroy Merlin]]  |  8,90€/m  |  17,80 €  |  71,90 €  |
|  Tube carré acier 30mm, longueur 746mm  |  2  |  Casto, Leroy Merlin  |  -  |  -  |  -  |
|  Tube carré acier 30mm, longueur 722mm  |  2  |  Casto, Leroy Merlin  |  -  |  -  |  -  |
|  Ecrous M8  |  64  |  -  |  -  |  -  |  -  |
|  Rondelle M8 16mm de diamètre extérieur  |  64  |  [[https://www.leroymerlin.fr/v3/p/produits/lot-de-20-rondelles-acier-zingue-diam-8-mm-standers-e127137|Leroy Merlin]]  |  3,50€/20  |  14,00 €  |  85,90 €  |
|  Patins caoutchouc bloque portes diamètre 25mm  |  4  |  Casto  |  -  |  -  |  -  |
|  Vis M6x20 BTR  |  36  |  [[https://www.leroymerlin.fr/v3/p/produits/lot-de-10-vis-metal-tete-cylindrique-acier-zingue-l-20-0-x-diam-6-mm-standers-e125490|Leroy Merlin]]  |  3,45€/10  |  13,80 €  |  99,70 €  |
|  Vis M6x30 BTR  |  41  |  [[https://www.leroymerlin.fr/v3/p/produits/lot-de-8-vis-metal-tete-cylindrique-acier-zingue-l-30-0-x-diam-6-mm-standers-e125489|Leroy Merlin]]  |  3,45€/10  |  13,80 €  |  113,50 €  |
|  Vis M6x40 BTR  |  4  |  [[https://www.leroymerlin.fr/v3/p/produits/lot-de-6-vis-metal-tete-cylindrique-acier-zingue-l-40-0-x-diam-6-mm-standers-e125482|Leroy Merlin]]  |  3,45€/6  |  3,45 €  |  116,95 €  |
|  Vis M6x50 BTR  |  4  |  [[https://www.leroymerlin.fr/v3/p/produits/lot-de-6-vis-metal-tete-cylindrique-acier-zingue-l-50-0-x-diam-6-mm-standers-e125483|Leroy Merlin]]  |  3,45€/6  |  3,45 €  |  120,40 €  |
|  Vis M6x40 HEX  |  8  |  -  |  -  |  -  |  -  |
|  Vis M6x50 HEX  |  6  |  -  |  -  |  -  |  -  |
|  Écrous M6  |  107  |  -  |  -  |  -  |  -  |
|  Vis M5x20 BTR  |  14  |  -  |  -  |  -  |  -  |
|  Vis M5x30 BTR  |  5  |  -  |  -  |  -  |  -  |
|  Écrous M5  |  19  |  -  |  -  |  -  |  -  |
|  Vis M4x30 BTR  |  4  |  -  |  -  |  -  |  -  |
|  Vis sans tête M4x6  |  4  |  -  |  -  |  -  |  -  |
|  Écrous M4  |  8  |  -  |  -  |  -  |  -  |
|  Vis M3x10 BTR  |  24  |  -  |  -  |  -  |  -  |
|  Vis M3x16 BTR  |  6  |  -  |  -  |  -  |  -  |
|  Écrous M3   |  10  |  -  |  -  |  -  |  -  |
|  Vis M2x10  |  6  |  -  |  -  |  -  |  -  |
|  Vis tôle 4.2x25  |  un sachet  |  -  |  -  |  -  |  -  |
|  Vis tôle 4.2x13  |  un sachet  |  -  |  -  |  -  |  -  |
|  Cornière alu 20x20  |  2 mètres  |  -  |  -  |  -  |  -  |
|  Plaque de MDF 754x604 épaisseur 22mm  |  1  |  -  |  -  |  -  |  -  |
|  Écrous M10  |  4  |  -  |  -  |  -  |  -  |
|  Rondelles M10  |  4  |  -  |  -  |  -  |  -  |
===== Photos =====

|  {{projets:opencnc:rs_cnc_printed_pieces_part.jpg?400}}  |

===== Ressources =====

  *[[https://www.lesimprimantes3d.fr/forum/topic/35468-choix-cnc-diy-open-maker-pro-vs-rs-cnc-vs-indymill/|Discussion forum 2020 sur différents modèles à construire]]
  *[[https://openbuilds.com/|Lots of CNC builds]]


==== Liste modèles ====

  *[[https://www.makerfr.com/cnc/rs-cnc32/|Maker FR RS-CNC32]]
  *[[https://www.mon-fablab.fr/openmakermachinepro/machine/descriptif|Open Maker Machine Pro]]
  *[[https://indystry.cc/indymill/|Indymill]]
  *[[https://www.maslowcnc.com/|Maslow CNC]] CNC sans cadre, suspendu, pratiques pour découpes de très grandes surfaces