3d:start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
3d:start [2023/08/31 09:54] – [Low Poly Workflow] mh3d:start [2024/12/19 11:05] (current) – [Useful shortcuts] mh
Line 1: Line 1:
 ====== 3D Modeling ====== ====== 3D Modeling ======
  
-This section will document what I wish to keep handy regarding [[https://blender.org|Blender 3D]], an advanced and powerful 3D modeling suite. It's free and open source so feel free to rush to their website, download it, and have fun as well. +This section will document what I wish to keep handy regarding [[https://blender.org|Blender 3D]].
  
 ===== Low Poly Workflow ===== ===== Low Poly Workflow =====
Line 12: Line 11:
 Then take each element into finer stages of detail step by step, don't try to model the elements from box to final in one go.  Then take each element into finer stages of detail step by step, don't try to model the elements from box to final in one go. 
  
-Use loop cuts to add mesh (''CTRL + R'') but be wary of adding too much to stay in the low poly. Move individual vertices around a little randomly.+Use loop cuts to add mesh (''CTRL + R'') but be wary of adding too much to stay in the low poly. Move individual vertices around a little randomly to give character.
  
 Make good use of the Mirror Modifier and Solidify Modifiers to speed up workflow on basic shapes and apply them only when you want to break the symmetry and add finer details (destructive modeling). Scale can be applied on shapes (''CTRL + A'') but it is not mandatory and modeling can be done with scales other than (1,1,1). Make good use of the Mirror Modifier and Solidify Modifiers to speed up workflow on basic shapes and apply them only when you want to break the symmetry and add finer details (destructive modeling). Scale can be applied on shapes (''CTRL + A'') but it is not mandatory and modeling can be done with scales other than (1,1,1).
Line 18: Line 17:
 Beams are useful elements on buildings to join parts together and hide overlaps. Beams are useful elements on buildings to join parts together and hide overlaps.
  
-Cut out windows and doors using the knife (''K'') tool in the base object. Then select the edges, duplicate and move them outwards, scale them down a bit, separate to make a new object, in that new object in edit mode extrude outwards and then add a solidify modifier. Careful that your normals face the right way. If you have mirrors not applied be sure to activate clipping so that the points on the mirror axes don't separate from each others when scaling down.+Cut out windows and doors using the knife (''K'') tool in the base object. Then select the edges, duplicate and move them outwards, scale them down a bit, separate to make a new object, in that new object in edit mode extrude outwards and then add a solidify modifier. Take care that your normals are facing the right way. If you have mirrors not applied be sure to activate clipping so that the points on the mirror axes don't separate from each others when scaling down.
  
 It's handy to start with a boxed shape then inset faces and extrude them and scale them down along the normal to get quick good looking volumes. It's handy to start with a boxed shape then inset faces and extrude them and scale them down along the normal to get quick good looking volumes.
Line 66: Line 65:
 Surfaces that are emissive will have a much better render in Cycles than in Eevee. Surfaces that are emissive will have a much better render in Cycles than in Eevee.
  
-When beveling you can press ''CTRL + B'' and then ''V'' to bevel a vertex and create a triangle face where the vertex was. Direct shortcut is ''CTRL + SHIFT + V''+When beveling you can press ''CTRL + B'' and then ''V'' to bevel a vertex and create a triangle face where the vertex was. Direct shortcut is ''CTRL + SHIFT + V''. When beveling vertices, use ''J'' to join opposite vertices that were created to re-triangulate the faces and correct the geometry.
 ===== Texturing ===== ===== Texturing =====
  
Line 207: Line 206:
 === Recap === === Recap ===
  
-  * Uses a bend modifier to create a circle with basic shapes. +  * Uses a bend modifier to create a circle with basic shapes : create a line of shapes + Modifier > Simple Deform > Bend (360°) and apply. 
   * Uses a nice simple low poly esthetic with bevels and moving a few vertices around   * Uses a nice simple low poly esthetic with bevels and moving a few vertices around
   * Shows the use of a lattice to parent an object or group of object to follow modifications made to the lattice (bends and such)   * Shows the use of a lattice to parent an object or group of object to follow modifications made to the lattice (bends and such)
Line 283: Line 282:
  
 ++++ ++++
 +
 +
 +==== Making Spiral meshes ====
 +
 +Use addon tool : Add Curve : Extra Objects.
 +
 +  * Add an Archemedian curve spiral.
 +  * Tweak the Turns, Steps, Radius Growth and Height properties before validating the spiral.
 +  * Go into the Data panel and under Geometry > Bevel add some Depth. Activate Fill Caps option.
 +  * Convert the curve to a mesh and go sculpt.
 +
 +----
 +
 +===== Exercises =====
 +
 +[[3d:exercises:start|3d Exercises]]
  
  
Line 302: Line 317:
   *''CTRL +/-'' : Select more / less of mesh (based on a first selection of faces or edges or vertices   *''CTRL +/-'' : Select more / less of mesh (based on a first selection of faces or edges or vertices
   *''SHIFT + S'' : Cursor selection pie menu   *''SHIFT + S'' : Cursor selection pie menu
 +  *''CTRL + Click'' : With a vertex selected will auto-select shortest path to the target vertex
 +  *''L'' : Select linked mesh (useful when hovering over meshes that intersect but are different objects)
  
 === Sculpting === === Sculpting ===
  • 3d/start.1693468447.txt.gz
  • Last modified: 2023/08/31 09:54
  • by mh