Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
composants:rpi_osmc [2019/01/02 16:45] – [Divers] mh | composants:rpi_osmc [2020/06/01 16:35] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 3: | Line 3: | ||
{{composants: | {{composants: | ||
- | ===== Résumé | + | ===== Summary |
- | La Raspberry | + | A Raspberry |
- | ===== Mettre une télécommande | + | ===== Sources management ====== |
- | //Les télécommandes émettent généralement dans une longueur d'onde de 940 nm et cette configuration nécessite une diode capable de capter dans ce spectre. Il est invisible à l'oeil nu mais les caméras vidéos (y compris les capteurs des téléphones) le voient comme une faible lueur violette.// | + | In the sources menu, when a keyboard is connected, pressing |
- | ==== Installation | + | NFS sources have to be properly configured on the server side (e.g. on the NAS if using one) and shared folders have to have permissions set up properly on remote hosts. |
+ | |||
+ | Sources management works best when using static IPs on the internal network and configuring the sources with direct IP addresses and proper protocols. For example : | ||
+ | |||
+ | < | ||
+ | nfs:// | ||
+ | smb:// | ||
+ | </ | ||
+ | |||
+ | ===== IR Remote control ===== | ||
+ | |||
+ | //IR remotes generally emit in a wavelength around 940nm, so we need a IR sensor. It's invisible to the eye but cameras (such as smartphones) can see a dim purple light.// | ||
+ | |||
+ | ==== Setup ==== | ||
*MyOSMC > Pi Config > Hardware Support | *MyOSMC > Pi Config > Hardware Support | ||
- | *Noter les pins GPIO | + | *Note GPIO pins |
- | *Celui qui nous intéresse est gpio_in_pin | + | *we need gpio_in_pin |
- | *Relier la diode en suivant le câbalge | + | *Plug the IR sensor accordingly |
- | *Vin sur 3.3V ou 5V en fonction | + | *Vin on 3.3V or 5V |
- | *GND sur RPi GND | + | *GND on RPi GND |
- | *OUT sur gpio_in_pin (18 sur la mienne le 12/2017) | + | *OUT on gpio_in_pin (18 on mine in 12/2017) |
*MyOSMC > Remotes | *MyOSMC > Remotes | ||
- | *Activer le script | + | *Active appropriate |
- | *Si aucun script | + | *If no script |
==== irrecord ==== | ==== irrecord ==== | ||
- | Aller dans un shell : EXIT >> | + | Log into a shell : EXIT >> |
- | Arrêter le service | + | Stop lircd service |
< | < | ||
Line 34: | Line 47: | ||
</ | </ | ||
- | Lancer | + | Launch |
< | < | ||
Line 40: | Line 53: | ||
</ | </ | ||
- | Redémarrer le service | + | Reboot |
< | < | ||
Line 46: | Line 59: | ||
</ | </ | ||
- | Le script demandera d' | + | Script will ask to press certain buttons. Full list can be found [[https:// |
===== Ressources ===== | ===== Ressources ===== | ||
Line 69: | Line 82: | ||
==== RPi 3 Pinout ==== | ==== RPi 3 Pinout ==== | ||
+ | |||
+ | ++++ GPIO Header | | ||
{{composants: | {{composants: | ||
+ | ++++ | ||
+ | |||
+ | === Power Button === | ||
+ | |||
+ | To wake up the RPi after halt, short pin #05 and GND. | ||
- | ===== Divers ===== | + | ==== Links ==== |
- | To wake up the RPi after halt, short pin #05 and GND | + | [[https:// |